MENU

Conventional fire control panel

Sigma CP – simple, dependable fire detection for everyday protection.

Overview

The Sigma CP range of conventional fire control panels are designed for the most demanding of conventional fire detection and alarm system applications. Easy to install, the Sigma CP is available with two, four or eight detection zones in standard or installation saving, ‘two-wire’ versions.

The extensive range of configuration features available ensure suitability for new installations or panel replacements on older systems.

Configuration options are stored in non-volatile memory and are easily accessed via an intuitive user interface, which enables the configuration data to be viewed and changed efficiently.

Sigma CP control panels are compatible with most standard, conventional detectors, call points and sounders and are also compatible with ‘two wire’ detector bases from Apollo and Hochiki.

Powerful Features

The simple and intuitive programming interface on Sigma CP panels allows simple configuration of many parameters by entering simple codes which are listed on the inner door look up table and in the operation and maintenance manual.

Connectivity

Sigma CP control panels have a dedicated ‘two-wire’ serial bus for connection of repeater panels, ancillary relay boards or zonal sounder extension boards. Up to seven units may be connected to the serial bus which can be up to 1200 metres in length.

Ease of Installation

The elegant and simple construction of the panel enables the chassis to be completely dismantled by removing just two screws.

Main Features

  • Two-wire and standard versions in two, four or eight zones
  • Compatible for use on BS5839: Part 1: 2017 installations
  • Two-wire repeaters and ancillary boards
  • Fully programmable using simple menu options
    • Adjustable sounder delay time
    • Sounder configuration options
    • Zonal sounder delay detectors only
    • Zonal sounder delay call points only
    • Coincidence input selection
    • I.S. Barrier selection by zone
    • Short circuit fire by zone
    • Non latching zones
    • Silent zones
    • Zone input delay
    • General panel configuration
  • Simple, single board construction
  • Installer friendly
  • Compatible with wide range of detection devices
  • Two monitored sounder outputs
  • Three Amp power supply
  • Auxiliary power output
  • Fully certified to BS EN54-2 and BS EN54-4

Technical Documentation

Click to download the documentation

Datasheets

System Diagram

Manuals

Certificates

Accessories

Sigma CP-R Sigma CP Sounder Controller Unit Sigma CP Ancillary PCB Line Continuity Monitoring Unit Relay Boards Plant Isolate/Audio Visual Remote Indicator Unit Docbox Tamper Resistant Vision Window
  • Sigma CP-R
  • Sigma CP Sounder Controller Unit
  • Sigma CP Ancillary PCB
  • Line Continuity Monitoring Unit
  • Relay Boards
  • Plant Isolate/Audio Visual
  • Remote Indicator Unit
  • Docbox
  • Tamper Resistant Vision Window

The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2, 4 or 8 zones and in mains powered (K versions) or 24V powered (E versions).

Sigma CP-R

The Sigma CP Sounder Board is compatible with all Sigma CP control panels which have operating software version V3.0 or above.

Sigma CP Sounder Controller Unit

The Sigma Ancillary Board is compatible with all Sigma CP and CP-R panels which have operating software version V2.0 or above.

Sigma CP Ancillary PCB

To use this method of monitoring, the breaking connection of the detector base must be fitted with a diode. To ensure correct operation over a wide supply voltage range and with up to 20 detectors removed, a Schottky type BYV-1060 is recommended. These devices are, however, very sensitive to electrostatic discharge and extra care should be taken when handling or cable testing.

 

Line Continuity Monitoring Unit

Easy to fit and wire for additional control functions or to expand the capability of existing relay outputs, these simple boards contains either one or four 24V DC relays, which can be used for any extra-low voltage switching applications.

Relay Boards

A range of indicator units with either red or yellow indicators to provide an audible and visual status of alarms, isolation’s or other functions.
These units are available with a keyswitch to silence the internal buzzer or a keyswitch to illuminate the indicator and buzzer. A volt-free contact is provided when the keyswitch is operated for ancillary control functions.

Plant Isolate/Audio Visual

Remote Indicator Units provide an extension for LED indicators on hidden detection devices to allow their status to be observed without having to expose the detection device itself.
All units have dual, bright LED indicators with a wide viewing angle that flash alternately to attract attention, and are available mounted to square or round metal plates for fitting to standard electrical back boxes.

Remote Indicator Unit

Designed to provide a convenient method of storing system test records, manuals, configuration files, keys and other documents or access arrangements for fire alarm and protection systems, the Sigma DocBox is finished and constructed in a similar manner to Sigma and Syncro AS fire alarm control equipment.

Docbox

The Tamper Resistant Vision Window is perfect for public areas where restricted access is necessary to prevent damage and unauthorised operation of the control panel. The cover features a fully welded steel construction and key lockable inner door making it robust and secure.

Tamper Resistant Vision Window

Get in touch. We're here to help.

Contact us